Before Reading These Instructions
We endeavor to give you the advantages of precise electronic and mechanical engineering, manufactured with carefully selected components, and
assembled by people who are proud of the reputation their work has built for our company. We know this product will bring you many hours of
enjoyment, and after you discover the quality, value and reliability we have built into it, you too will be proud to be a member of our family.
Specifications
Panasonic welcomes you to our constantly growing family of electronic products owners.
CD Player/Receiver
General
FM Stereo Radio
Power supply
:12 V DC (11 – 16 V DC), negative
ground
Frequency range
:87.5 MHz – 108 MHz
:6 dB/µV (75 Ω)
:30 Hz – 15 kHz ( 3 dB)
:75 dB
:35 dB (1 kHz)
:75 dB
CQ-C1121W/C1101W/C1001W
Usable sensitivity
Current consumption
Maximum power output
:Less than 2.2 A (CD mode; 0.5 W 4
channels)
Frequency response
Alternate channel selectivity
Stereo separation
Image rejection ratio
IF rejection ratio
Signal to noise ratio
This operating instruction manual is for 3 models CQ-C1121W, CQ-C1101W and CQ-C1001W. All illustrations throughout this
manual represent model CQ-C1121W unless otherwise specified. The following table describes the differences among 3 models.
:50 W x 4 (at 1 kHz), volume control
maximum (for CQ-C1121/C1101W)
:45 W x 4 (at 1 kHz), volume control
maximum (for CQ-C1001W)
:Bass: 12 dB at 100 Hz, Treble: 12
dB at 10 kHz
:100 dB
:62 dB
Operating Instructions
Tone adjustment range
Models
CQ-C1121W
Rotary knob
Yes (Included)
CQ-C1101W
Rotary knob
No
CQ-C1001W
Button
No
AM Radio
Features
Volume control
Speaker impedance
Pre-amp output voltage
Pre-amp output impedance
Dimensions (W x H x D)
Weight
:4 – 8 Ω
Frequency range
Usable sensitivity
:531 kHz – 1 602 kHz
:28 dB/µV (S/N 20 dB)
:2.5 V (CD mode, 1 kHz, 0 dB)
:200 Ω
Remote control function
BAND
CQ-C1121W
:178 x 50 x 160 mm
:1.3 kg
APM
CLOCK
PWR
E
MUTE
7
8
9
10
11
12
SQ/SCAN
SRC
DISP
Pre-amp. output connector Rear/Front
Rear
Rear
1
2
3
4
5
6
CD Player
(CQ-C1121W)
Sampling frequency
:8 times oversampling
:1 bit DAC System
:Astigma 3–beam
:Semiconductor laser
:790 nm
DA converter
Pick-up type
Light source
Wave length
Frequency response
Signal to noise ratio
Total harmonic distortion
Wow and flutter
Channel separation
:20 Hz – 20 kHz ( 1 dB)
:96 dB
:0.01 % (1 kHz)
:Below measurable limits
:75 dB
Note:
¡ Specifications and design are subject to modification without
notice due to improvements.
¡ Some figures and illustrations in this manual may be different
from your product.
Accessories
POWER
PWR
MUTE
Operating Instructions
(English: YFM284C450ZA)
(êÛÒÒÍËÈ: YFM284C451ZA)
Remote Control Unit
(include a battery, only
for CQ-C1121W)
(EUR7641020)
Mounting Collar *
VOL
MODE
TUNE
(FX0214C384ZA)
TRACK
BAND
CAR AUDIO
Q'ty: 1
(
: YFM284C452ZA)
Trim Plate *
(YFC054C081ZA:
CQ-C1121/1101W)
(YFM284C453ZA :
)
Q'ty: 1
Q'ty: 1 set
Lock Cancel Plate
(FX0214C385ZA)
Installation Instructions
(YFM284C449ZA)
(YFC054C079ZA: CQ-C1001W)
Q'ty: 1
Q'ty: 2
Q'ty: 1
Q'ty: 1
Q'ty: 1
Power Connector
(YEAJ02877)
Q'ty: 1
Mounting Bolt
(YEJV014C002N)
Rubber Bushing
(YFS014C095ZA)
Matsushita Electric Industrial Co., Ltd.
Notes:
¡ The number in parentheses underneath each accessory part name is the part number for maintenance and service.
¡ Accessories and their part numbers are subject to modification without prior notice due to improvements.
¡ Mounting Collar and Trim Plate are mounted on the main unit at shipment. *
¡Please read these instructions carefully before using this product and keep this manual for future reference.
YFM284C450ZB TAMACO1104-1124
Printed in China
Preparation
Maintenance
Safety Information
Pull the insulation film out from
the backside of the remote con-
trol gently.nly
Note: Battery Information:
Battery Type: Panasonic lithium battery (CR2025) (Included
in the remote control)
Battery Life: Approximately 6 months under normal use (at
room temperature)
Your product is designed and manufactured to ensure the minimum of maintenance. Use a soft cloth for routine
exterior cleaning. Never use benzine, thinner, or other solvents.
■
■
Read the operating instructions for the unit and all other compo-
nents of your car audio system carefully before using the system.
They contain instructions about how to use the system in a safe and
effective manner. Panasonic assumes no responsibility for any prob-
lems resulting from failure to observe the instructions given in this
manual.
This manual uses pictographs to show you how to use the product
safely and to alert you to potential dangers resulting from improper
connections and operations. The meanings of the pictographs are
explained below. It is important that you fully understand the mean-
ings of the pictographs in order to use this manual and the system
properly.
❑
❑
Do not install the product where it is exposed to strong
vibrations or is unstable.
Caution
Avoid slanted or strongly curved surfaces for installation. If the
installation is not stable, the unit may fall down while driving and
this can lead to an accident or injury.
Observe the following cautions when using this
unit.
Keep the sound volume at an appropriate level.
Keep the volume level low enough to be aware of road and traffic
conditions while driving.
This unit is designed for use exclusively in automo-
biles.
Do not operate the unit for a prolonged period with the
engine turned off.
Operating the audio system for a long period of time with the
engine turned off will drain the battery.
Do not expose the unit to direct sunlight or excessive
heat.
Otherwise these will raise the interior temperature of the unit,
and it may lead to smoke, fire, or other damage to the unit.
Do not use the product where it is exposed to water,
moisture, or dust.
Exposure of the unit to water, moisture, or dust may lead to
smoke, fire, or other damage to the unit. Make especially sure
that the unit does not get wet in car washes or on rainy days.
Installation Angle
❑
The product should be installed in a horizontal position with the
front end up at a convenient angle, but not more than 30˚.
The user should bear in mind that in some areas there may be
restrictions on how and where this unit must be installed.
Consult your dealer for further details.
This pictograph intends to alert you to the presence of
important operating instructions and installation instruc-
tions. Failure to heed the instructions may result in
This pictograph intends to alert you to the presence of
important operating instructions and installation instruc-
tions. Failure to heed the instructions may result in
❑
❑
If the replaced fuse fails, contact your nearest authorized Panasonic Service center.
The 24-hour system is used for the clock.
Clock Display at Power Off
Press [DISP] (Display) to change the display.
Warning
Caution
severe injury or death.
injury or material damage.
Turn the ignition switch
until the accessory indica-
1
C
ON
❑
❑
❑
Wear gloves for safety. Make sure that wiring is com-
pleted before installation.
To prevent damage to the unit, do not connect the
power connector until the whole wiring is completed.
Do not connect more than one speaker to one set of
speaker leads. (except for connecting to a tweeter)
AC
Warning
¡ Use fuses of the same specified rating (15 A). Using substitutes or fuses with higher ratings, or connecting the unit direct-
ly without a fuse could cause fire or damage to the unit. If the replaced fuse fails, contact your nearest authorized
Panasonic Service Center.
tor lights.
Display off
❑
❑
Press [SRC] (PWR:
Power).
Observe the following warnings when installing.
❑
2
Warning
Disconnect the lead from the negative (–) battery termi-
nal before installation.
Wiring and installation with the negative (–) battery terminal con-
nected may cause electrical shock and injury due to a short circuit.
Some cars equipped with the electrical safety system have specific
procedures of battery terminal disconnection.
FAILURE TO FOLLOW THE PROCEDURE MAY LEAD TO THE
UNINTENDED ACTIVATION OF THE ELECTRICAL SAFETY SYSTEM
RESULTING IN DAMAGE TO THE VEHICLE AND PERSONAL
INJURY OR DEATH.
Never use safety-related components for installation,
grounding, and other such functions.
Do not use safety-related vehicle components (fuel tank, brake,
suspension, steering wheel, pedals, airbag, etc.) for wiring or fix-
ing the product or its accessories.
Installing the product on the air bag cover or in a location
where it interferes with airbag operation is prohibited.
Observe the following warnings when using this
unit.
The driver should neither watch the display nor operate
the system while driving.
Watching the display or operating the system will distract the driv-
er from looking ahead of the vehicle and can cause accidents.
Always stop the vehicle in a safe location and use the parking
brake before watching the display or operating the system.
Press [DISP] (CLOCK).
3
Observe the following cautions when handling the
battery for the remote control unit.
●
●
Clock display
❑
Use only specified battery (CR2025).
Match the polarity of the battery with the (+) and (–) marks in
the battery case.
Anti-Theft System
Hold down [DISP] (CLOCK) for more than
2 seconds.
4
This unit is equipped with a removable face plate. Removing this face plate makes the unit totally inoperable.
●
●
Replace dead battery as soon as possible.
Remove the battery from the remote control unit when not using
it for an extended period of time.
Insulate the battery (by placing them in a plastic bag or covering
them with vinyl tape) before disposal or storage.
Dispose of the battery according to the local regulations.
Do not disassemble, recharge, heat or short the battery. Do not
throw a battery into a fire or water.
Observe the following cautions when installing.
Refer wiring and installation to qualified service per-
sonnel.
Installation of this unit requires special skills and experience. For
maximum safety, have it installed by your dealer. Panasonic is
not liable for any problems resulting from your own installation
of the unit.
Follow the instructions to install and wire the product.
Not following the instructions to properly install and wire the
product could cause an accident or fire.
❑
❑
Use the proper power supply.
❑
❑
●
This product is designed for operation with a negative grounded
12 V DC battery system. Never operate this product with other bat-
tery systems, especially a 24 V DC battery system.
Caution
Adjust the hour.
5
¡ This face plate is not waterproof. Do not expose it to
water or excessive moisture.
¡ Do not remove the face plate while driving your car.
¡ Do not place the face plate on the dashboard or nearby
areas where the temperature rises high.
¡ Do not touch the contacts on the face plate and the main
unit, since this may result in poor electrical contact.
¡ If dirt or other foreign substances get on the contacts,
wipe them off with a clean and dry cloth.
●
●
Keep batteries and insulation film out of reach of infants.
Batteries and insulation film can be ingested, so keep them out of
the reach of infants. If an infant ingests a battery or insulation film,
please seek immediate medical attention.
Protect the Deck Mechanism.
Do not insert any foreign objects into the slot of this unit.
❑
❑
[[]: sets the hour ahead.
❑
❑
In case of battery leakage
[]]: sets the hour back.
Check for piping, gasoline tank, electric wiring, and other
items before installing the product.
If you need to open a hole in the vehicle chassis to attach or wire
the product, first check where the wire harness, gasoline tank, and
electric wiring are located. Then open the hole from outside if pos-
sible.
●
●
●
Thoroughly wipe the battery liquid off the battery case and insert
new battery.
If any part of your body or clothing comes into contact with bat-
tery liquid, wash it with plenty of water.
If battery liquid comes into contact with your eyes, wash them
with plenty of water and get immediate medical attention.
❑
❑
Press [DISP] (CLOCK).
6
Take care not to damage the leads.
When wiring, take care not to damage the leads. Prevent them
from getting caught in the vehicle chassis, screws, and moving
parts such as seat rails. Do not scratch, pull, bend or twist the
leads. Do not run them near heat sources or place heavy objects
on them. If leads must be run over sharp metal edges, protect
the leads by winding them with vinyl tape or similar protection.
Do not disassemble or modify the unit.
Do not disassemble, modify the unit or attempt to repair the prod-
uct yourself. If the product needs to be repaired, consult your
dealer or an authorized Panasonic Service Center.
Removing
Mounting
Adjust the minute.
7
Turn off the power.
Slide the left side of the removable face
plate in place.
❑
❑
❑
Never install the product in a location where it interferes
with your field of vision.
1
2
1
❑
❑
❑
Do not use the unit when it is out of order.
Press [
open.
]. The removable face plate will
If the unit is out of order (no power, no sound) or in an abnormal
state (has foreign objects in it, is exposed to water, is smoking, or
smells), turn it off immediately and consult your dealer.
Never have the power cord branched to supply other
equipment with power.
After installation and wiring, you should check the nor-
mal operation of other electrical equipment.
The continuation of their using in abnormal conditions may cause
fire, electrical shock or a traffic accident.
In the case of installation to an airbag-equipping car,
confirm warnings and cautions of the vehicle manufactur-
er before installation.
❑
❑
Use the designated parts and tools for installation.
Use the supplied or designated parts and appropriate tools to
install the product. The use of parts other than those supplied or
designated may result in internal damage to the unit. Faulty
installation may lead to an accident, a malfunction or fire.
Do not block the air vent or the cooling plate of the unit.
Blocking these parts will cause the interior of the unit to over-
[[]: sets the minute ahead.
Press the right end of removable face plate
until a “click” is heard.
2
[]]: sets the minute back.
Pull it out toward you.
The remote control unit should not lie about in the car.
If the remote control unit lies about, it could fall on the floor while
driving, get wedged under the brake pedal, and lead to a traffic
accident.
Refer fuse replacement to qualified service personnel.
When the fuse blows out, eliminate the cause and have it replaced
with the fuse prescribed for this unit by a qualified service engi-
neer. Incorrect replacement of the fuse may lead to smoke, fire,
and damage to the product.
3
Press [DISP] (CLOCK).
8
2
1
❑
heat and will result in fire or other damage.
Notes:
❑
❑
Make sure the leads do not interfere with driving or get-
1
¡ “AdJ” is displayed before adjusting the clock.
¡ Hold down []] or [[] to change numbers rapidly.
ting in and out of the vehicle.
Insulate all exposed wires to prevent short circuiting.
2
Caution
THIS PRODUCT UTILIZES A CLASS I LASER.
USE OF CONTROLS OR ADJUSTMENTS OR PERFORMANCE OF PROCEDURES OTHER THAN THOSE SPECIFIED HEREIN MAY RESULT
IN HAZARDOUS RADIATION EXPOSURE.
DO NOT OPEN COVERS AND DO NOT REPAIR YOURSELF. REFER SERVICING TO QUALIFIED PERSONNEL.
|
Miele Washer w 304 plus User Manual
Multi Tech Systems Network Card MultiConnect Adapter User Manual
Murray Lawn Mower MB1842LT User Manual
Niles Audio Speaker CM6PR User Manual
NordicTrack Home Gym 305100 User Manual
Novatel Card Game OM 20000041 User Manual
Oreck Vacuum Cleaner PA 0513 DU User Manual
Oricom Cordless Telephone eco5100 Series User Manual
Panasonic DVD Recorder DMR EZ47 User Manual
Paradyne Network Card 3162 DSU CSU User Manual